MWCNT/ E 复合材料的制备及性能

利用三辊研磨分散技术制备了MWCNT/ E 复合材料。通过调节三辊研磨机入料辊和中辊的间
距,使MWCNT 在环氧树脂中均匀分散。所制备的MWCNT/ E 复合材料与纯环氧树脂相比,拉伸强度提高了
22%,弯曲强度提高了15%,导电性和导热性都得到明显改善。     

碳纤维复合壳体用基体环氧树脂研究进展

介绍了固体火箭发动机碳纤维缠绕用基体环氧树脂的种类、选择原则及适于碳纤维缠绕用基体树脂的研究进展.     

三种纳米碳材料吸波涂层设计及性能

对纳米炭黑(UC)、特导纳米炭黑(L6)、碳纳米管(CNT)三种材料在8～18 GHz波段吸波涂层进行了优化设计及吸波性能分析.结果表明,三种材料的复介电常数随着纳米碳材料质量分数的增加,其实部和虚部均以不同的速度增大.利用理论计算的Cole-Cole图,结合实验测得的复介电常数,求解出这三种材料理想的介电常数,材料的质量分数和吸波涂层的匹配厚度.结果表明,CNT的吸波效果最好,当CNT质量分数为20％涂层、厚度为1.6mm时,反射衰减率在11.2～ 15 GHz均优于-10 dB吸收峰最大值,达到29.6 dB.     

Low-dose carbon ion irradiation effects on DNA damage and oxidative stress in the mouse testis

To investigate the effects of low-dose carbon ion irradiation on reproductive system of mice, the testes of outbred Kunming strain mice were whole-body irradiated with 0, 0.05, 0.1, 0.5 and 1 Gy, respectively. We measured DNA double-strand breaks (DNA DSBs) and oxidative stress parameters including malondialdehyde (MDA) content, superoxide dismutase (SOD) activity, and testis weight and sperm count at 12 h, 21 d and 35 d after irradiation in mouse testis. At 12 h postirradiation, a significant increase in DNA DSB level but no pronounced alterations in MDA content or SOD activity were observed in 0.5 and 1 Gy groups compared with the control group. At 21 d postirradiation, there was a significant reduction in sperm count and distinct enhancements of DSB level and MDA content in 0.5 and 1 Gy groups in comparison with control. At 35 d postirradiation, the levels of DNA DSBs and MDA, and SOD activity returned to the baseline except for the MDA content in 1 Gy (P < 0.05), while extreme falls of sperm count were still observed in 0.5 (P < 0.01) and 1 Gy (P < 0.01) groups. For the 0.05 or 0.1 Gy group, no differences were found in DNA DSB level and MDA content between control and at 12 h, 21 d and 35 d after irradiation, indicating that lower doses of carbon ion irradiation have no significant influence on spermatogenesis processes. In this study, male germ cells irradiated with over 0.5 Gy of carbon ions are difficult to repair completely marked by the sperm count. Furthermore, these data suggest that the deleterious effects may be chronic or delayed in reproductive system after whole-body exposure to acute high-dose carbon ions.     

基于黑盒测试环境的交会对接软件时序分析技术及应用

航天器空间交会对接难度大,GNC软件对任务的完成起到重要作用.由于交会对接控制软件功能复杂,时序要求严格,这对软件测试提出了很高的要求.基于黑盒测试环境,利用FPGA设计方法和时序分析技术,实现了对交会对接软件重要数据运行时序的捕获和对上下行信号相位关系的跟踪,完善了故障触发和上行注入手段.该测试环境在交会对接软件研制过程中起到重要作用.     

Carbon dioxide dynamics of combined crops of wheat,cowpea, pinto beans in the Laboratory Biosphere closed ecological system

A mixed crop consisting of cowpeas, pinto beans and Apogee ultra-dwarf wheat was grown in the Laboratory Biosphere, a 40 m³ closed life system equipped with 12,000 W of high pressure sodium lamps over planting beds with 5.37 m² of soil. Similar to earlier reported experiments, the concentration of carbon dioxide initially increased to 7860 ppm at 10 days after planting due to soil respiration plus CO₂ contributed from researchers breathing while in the chamber for brief periods before plant growth became substantial. Carbon dioxide concentrations then fell rapidly as plant growth increased up to 29 days after planting and subsequently was maintained mostly in the range of about 200–3000 ppm (with a few excursions) by CO₂ injections to feed plant growth. Numerous analyses of rate of change of CO₂ concentration at many different concentrations and at many different days after planting reveal a strong dependence of fixation rates on CO₂ concentration. In the middle period of growth (days 31–61), fixation rates doubled for CO₂ at 450 ppm compared to 270 ppm, doubled again at 1000 ppm and increased a further 50% at 2000 ppm. High productivity from these crops and the increase of fixation rates with elevated CO₂ concentration supports the concept that enhanced CO₂ can be a useful strategy for remote life support systems. The data suggests avenues of investigation to understand the response of plant communities to increasing CO₂ concentrations in the Earth’s atmosphere. Carbon balance accounting and evapotranspiration rates are included.     

碳纳米管及连续碳纤维增强复合材料研究进展

文章综述了近年来碳纳米管及连续碳纤维增强复合材料在工程应用、材料体系、表面改性等方面的研究进展,并对碳纳米管和连续碳纤维共同增强复合材料在航天工程领域的应用进行了展望。     

FCVI中气体温度与预制体温度的关系

强制流动热梯度化学气相渗透（ＦＣＶＩ）作为一种制备碳基、陶瓷基复合材料的新工艺,克服了传统ＣＶＩ中气体扩散传输与预制体渗透性的限制,可在短时间内制备出密度均匀、性能优良的制件。本文分析了在ＦＣＶＩ工艺过程中预制体温度与气体温度的区别,并从理论上推导出了ＦＣＶＩ中气体温度与预制体温度间的关系。     

碳/碳复合材料用基体先驱体研究进展

综述了碳／碳复合材料用基体先驱体如沥青、酚醛树脂、邻苯二甲腈树脂和炔类树脂的合成及改性研究。为开发新一代低成本、高性能碳／碳复合材料提供了方向。     

Cf/SiC复合材料先驱体转化法浸渍工艺条件优化

主要研究了先驱体转化法制备碳纤维三维编织物增强陶瓷基复合材料的浸渍工艺条件,探讨了不同温度,压力对PCS／DVB溶液法和PCS熔融法浸渍效率的影响,优化出最佳浸渍工艺参数。结果表明,温度对PCS／DVB溶液粘度影响较大,升高温度可急剧降低PCS／DVB溶液的粘度,有利于浸渍。PCS／DVB溶液法浸渍的最佳工艺参数为：50－60度,2MPa,PCS熔融法浸渍的最佳工艺参数为：300度,2MPa,采用PCS／DVB溶液法浸渍时的浸渍效率优于PCS熔融法,经四个浸渍裂解周期后溶液法制备的材料密度（1．53g/cm3-1.61g/cm3)明显优于先驱体熔融法（1．43g/cm3-1.52g/cm3)